返回主站|会员中心|保存桌面|手机浏览
普通会员

宁津县晟成风电设备有限公司

风力发电机,控制器逆变器,蓄电池,太阳能发电板,打井

产品分类
  • 暂无分类
站内搜索
 
友情链接
  • 暂无链接
首页 > 供应产品 > **山东晟成3000瓦小型风力发电机 低风速环保家用风力发电机
**山东晟成3000瓦小型风力发电机 低风速环保家用风力发电机
浏览: 629
品牌: 晟成
输出功率: 4000瓦
产地: 山东
单价: 9025.00元/套
最小起订量:
供货总量: 50 套
发货期限: 自买家付款之日起 天内发货
有效期至: 长期有效
最后更新: 2021-10-11 12:05
 
详细信息
输出功率 4000瓦
产地 山东
产品认证 CE
额定功率 3000瓦
额定频率 50HZ
输出电压 96v
相数 三相
叶片数目 3片
品牌 晟成
型号 FD4-3.0
加工定制

供应晟成3KW中小型发电机设备可供中小型办公商场用电节约成本

【安装说明】

一、风力发电机的风能转换原理和安装场地的选择

 风能就是运动着的风的动能,风力发电机就是将风的动能转变为旋转动能,在转化为电能,风能的方程式是风速的3次函数。就是说风速每增加10%风力发电机的功率就增加30%。几乎在所有的场地,风机竖立的越高,风速就越大。所以风机应竖立得尽量高和尽可能的远离障碍物。风力发电机到逆变器和电瓶的距离越短,电缆在传输过程的耗能就越少,反之耗能大,发电量就会越少。一般建议电缆的长度不应超过15米。

  二、用混凝土固定底座,地锚。待混凝土固化后开始下步安装。

三、固定电机组合体和立杆,将防水线连接电机引线,用绝缘胶布包好,再穿入回转体之前把电缆线打一个结,防止拽断电机内接线,穿入后把电缆线并接。(拧在一起短路,使风机风叶不能随意转动。)

四、钢丝拉线要在立杆“拉线耳朵”中间缠绕一圈,然后用锁扣锁死,不能将拉线直接拉住耳朵,那样风大时容易拉断拉线耳朵,造成危险。

五、叶片安装要按顺时针1、2、3的顺序固定在夹盘上,(风叶跟底部有标记)叶片凹面迎风,拧紧夹盘螺丝,然后将夹盘穿到电机轴上,放上弹簧片,将螺母拧紧,然后安装风帽。

六、将尾舵杆,尾板安装好,切记一定要系尾舵绳,以备风大时掉转风轮方向。

七、将下立杆与底座连接,立直发电机,紧固地脚螺丝。将调紧器调到最松位置,用挂钩钩住地锚,将拉线扯向三个地锚。调紧松紧器使风机直立地面,然后用60CM的钢丝(用户需自备)将拉线与地锚钩环处缠绕一圈后用锁扣琐死,防止松紧器断裂或拉线松动脱钩造成风机倾倒。(如图一)

八、电器的安装

1、将充好电的电瓶串联,将正负极一一接到逆变器的正负极,(不可接反,否则将烧坏电器系统)然后将风机用尾舵绳侧风,停止风机,将风机三根线与逆变器接口连接,不分极性,最后检查各个部位是否连接好,确认正常后,使风机转动,就可使用逆变器了。(如图二)

2、蓄电池要放在室内,通风的地方,把所有的接线头部位都涂上油脂或防腐材料。为避免电磁干扰,蓄电池与逆变器间的导线要短于2.5米。



使用注意事项,用户必读。

※1、安装或拆卸风机,应选择无风的天气。

2、风机正常运转时不要在风机底座8米范围内流动。

3、应随时听天气预报,遇有大风天气时应拉偏风机降低转速,如遇超过额定风速一定要及时预先放倒风机。

4、要经常检查底座、松紧器,拉线的张力及花篮锁扣,螺丝是否有松动或损坏的现象,如发现应及时处理,不可拖拉,防止发生事故。

5、发电机再运转中发现异常响声或松动,应及时停机检查,并及时处理以免损坏发电机。

6、电瓶充满后应使风机偏侧,降低转速。

7、在正常运转中电瓶线不可断开或虚接,如要更换蓄电池应停止风机,否则将烧坏逆变器

"Installation instructions"

The wind energy conversion principle, wind turbines and installation site selection

Wind is the movement of the kinetic energy of the wind, the wind generator is to transform the kinetic energy of the wind as the rotational kinetic energy, in a converted to electrical energy, wind energy equation is the three function of wind speed. 10% increase is wind speed of wind turbine power is increased by 30%. Erected in almost all fields, the fan is higher, the greater the wind speed. So the fan should be erected as high and as far as possible away from obstacles. Wind turbines to the inverter and the shorter the distance, the battery cable in transmission process the less energy consumption, and energy consumption, electricity generation will be less. Generally suggested that the length of the cable should be not more than 15 meters.

Second, fixed base with concrete, anchor. For concrete curing step start after installation.

Three, fixed motor assembly and poling, connect waterproof line motor fuses, wrapped in electrical tape, to wear into the solid of revolution before the cable tie a knot, prevent pulled off the motor wiring, after through the cable and connect. Screw together (short circuit, to rotate the fan blades cannot optional.)

Four, steel wire cord to in the middle of the vertical pole "pull the ear" wrapped around a circle, then lock with the lock, pull pull the ear directly, can not be so easy to break when windy anchor ear and dangerous.

Five, the blade installation according to clockwise order of 1, 2, 3 on the chuck, concave (marked) at the bottom of the blades and blade windward, tighten the clamp screw, and then wear the chuck on the motor shaft, put spring leaf, tighten nut, then install the cap.

Six, the tail rudder, tail plate installed, be sure to tie rope tail rudder, for turning large wind turbines.

Seven, connect the stud and the base, stand straight motor, tighten bolts. Tighten device will be dispatched to the location, with hook hook anchor, the pull pull toward the three anchor. Tighten elastic device make the fan upright on the ground, then use 60 cm wire need to bring your own (user) will stay with anchor shackle in winding with lock of zobah died after a circle, to prevent elastic fracture or loose thread decoupling fan pour. (as shown in figure 1)

Eight, the installation of electrical appliances

1, will be charged the battery of electric series, will receive inverter is the cathode is negative, (not against, otherwise will burn out electrical system) and then use fan tail rudder rope cross wind, stop the fan, the fan three wires connected to the inverter interface, regardless of polarity, and finally check if all parts connection good, confirmed after normal, to rotate the fan, can use the inverter. (as shown in figure 2)

2, the battery should be placed indoor and ventilated places, all the wiring head a grease or anti-corrosion materials. To avoid electromagnetic interference, between the battery and inverter leads to shorter than 2.5 meters.

Using the matters needing attention, the user must read.

※ 1 install or remove the fan, should choose the windless weather.

2 fan during normal operation, not within the scope of the 8 m fan base flow.

3, should listen to the weather forecast at any time, in case of strong wind weather should pull partial fan to reduce the speed, must be in a timely manner in case of more than the rated wind speed down the fan in advance.

4, often should check the base, elastic, pull tension and basket lock, screws are loose or damaged phenomenon, such as found that should be handled in time, do not drag, prevent the accident.

5, generators of abnormal noise during operation or loose again, should be timely stop the inspection, and processed in a timely manner so as not to damage the generator.

6, after the battery is full side should make fan, reduce speed.

7, do not disconnect the battery line in normal operation or empty, if you want to replace the battery to stop the fan, otherwise will burn out inverter non, such as found that should be handled in time, do not drag, prevent the accident.




功  率

3KW

风轮直径(blade diameter)

4m

叶片材质(material of the blades)

增强玻璃钢 Fiberglass-Reinforced Plastic

额定风速(rated speed)

10m/s

额定功率(rated Power)

3KW

最大功率(max Power)

4.5Kw

最大启动扭力矩n/m(Max start torsional moment n/m)

<3

输出电压

220V

启动风速

3(m/s)

额定转速(转/分)

300

工作风速

3.0-25(m/s)

安全风速

40(m/s)

控制器型号

240V100A

发电机类型

三相交流永磁   3-phase AC PM

主体重量

260kg

建议配套蓄电池

12v100AH二十块   


询价单